LWS eARDWP Help Tips

INTRODUCTION
  1. General Office Phone: Enter the phone number for the main office. This phone number will be posted on the Drinking Water Watch for the general public. It can be accessed at: https://sdwis.waterboards.ca.gov/PDWW

  2. Certification for Reduction of Annual Fees for Public Water Systems Serving Disadvantaged Community (DAC ):

    §64310. Reduction of Fees for Public Water Systems Serving Disadvantaged Community.

    (a) A public water system must pay the full amount of the annual fee unless it requests and receives from the State Board a determination that its annual fees are reduced because it is a community water system that serves a disadvantaged community in which case the fee to be paid is the amount for a disadvantaged community as shown in Table 64305-A.

    (b) To qualify for the reduction provided for in subsection (a), a public water system must certify, and provide documentation to the State Board upon request, that it serves a disadvantaged community.

  3. Report Submitted By: The information included in this section is automatically filled based on the eARDWP user’s profile. If the information in this section is incorrect, the user must update their user profile on the MY PROFILE tab before the report is submitted. You must be logged in to change your user profile. Note: Your name and title, email address, and work phone number are disclosable report information that may be obtained through the Public Records Act.

  4. Comments: Comment boxes are provided throughout the eARDWP to allow the user to provide discussion or clarification on their responses provided in that section of the report. These comment boxes can accommodate up to 4000 characters.

    SECTION 1. PUBLIC WATER SYSTEM CONTACTS.

  5. Public Water System Contacts: This section of the report will be pre-filled with current water system contact information in the Division of Drinking Water database (Safe Drinking Water Information System or SDWIS). Overtype the contact information to provide any necessary updates. The option to add up to four (4) new contacts is provided at the end of this section.

  6. Phone Type Definitions.

    PHONE TYPE DEFINITIONS
    Business The BUSINESS phone type is treated as a public phone number and will appear in Drinking Water Watch (https://sdwis.waterboards.ca.gov/PDWW/), which can be viewed by the public, if the General Office phone number is not provided (see Water System Information section under the Intro tab).
    Home The HOME phone type is treated as a private phone number. If you use your home or personal phone number as your business number, use the HOME phone type instead and leave the BUSINESS phone type blank. Only the BUSINESS phone type will appear in Drinking Water Watch (https://sdwis.waterboards.ca.gov/PDWW/), which can be viewed by the public, if the General Office phone number is not provided (see Water System Information section under the Intro tab).

  7. Contact Type Definitions.

    NOTE: A person may be assigned multiple contact types. For example, the owner may also be both the Administrative Contact and Financial Contact.
    CONTACT TYPE DEFINITIONS
    Administrative Contact (AC) The person who is legally responsible for ensuring that the Public Water System maintains compliance with SDWA requirements. The person to whom Division of Drinking Water mass mailings, enforcement letters and correspondences would be addressed, such as the Board of Directors, General Manager or CEO. Each water system must have one and only one AC.

    Please provide an email address for the Administrative Contact as most email communication, particularly email blasts, from the Division of Drinking Water will be sent to the email address of the Administrative Contact.
    Financial Contact (FC) The person who receives Division of Drinking Water invoices and issues payments. Each water system must have one and only one FC.
    Owner The person or entity named in the water supply permit. If not the same as the Administrative Contact, this would then be the legal owner or entity that is legally responsible for the Public Water System.
    Designated Operator in Charge Chief Operators. This person could also be the Administrative Contact, Owner, or Contract Operator. Must be a certified operator for community and nontransient noncommunity water systems.
    Operator Contact Shift Operators. Must be a certified operator for community and nontransient noncommunity water systems.
    Emergency Contact The person who assists with coordinating emergency activities (e.g. collecting samples, conducting public notification, corresponding with the Division of Drinking Water.)
    Water Quality Contact The person who receives water quality email updates from the Division of Drinking Water. The person responsible for coordinating or conducting water quality monitoring and/or sample collection. Email address required for electronic mailing.
    Legal Contact Public water system’s attorney or legal counsel.
    CONTRACT Operator Contact The person or company with whom the water system has a contract to operate or assist in the operation of the water system.
    Funding Contact The person who receives funding (State Revolving Fund) email updates from the Division. This person is the representative of the water system for projects receiving Safe Drinking Water Act funds.

  8. Add Additional Contact. Up to four additional contacts may be added.

    SECTION 2. POPULATION SERVED.

  9. Provide Season: Provide the dates (month and day) that cover the increase in seasonal population. For example, if it is only during the summer, the Begin Date could be 06/01 and the End Date could be 09/30. Month must be between 1 and 12. Day must two digits between 1 and 31.

    SECTION 3. CONNECTIONS.

  10. Number of NON-residential customers required to have dedicated outdooring irrigation meters. A dedicated outdoor irrigation meter only measures outdoor water and does not meter any water used indoors. The response should exclude agricultural connections.

    SECTION 4. GROUNDWATER (GW) AND SURFACE WATER (SW) SOURCES.

  11. Active Groundwater Intakes (Wells) - Applies only to groundwater wells owned by the water system. Purchased groundwater supplies should be counted under Active Purchased Water (GW) Connections.

  12. Active Surface Water Intakes (Raw) – raw (untreated) surface water intakes. Applies only to intake structures owned by the water system itself such as intakes in lakes, rivers, etc. Purchased untreated surface water obtained via a pipeline is not considered an intake, but should be counted as an Active Purchased Water (SW) Connections.

  13. Active Purchased Water (GW) Connections – includes both raw and treated purchased groundwater connections.

  14. Active Purchased Water (SW) Connections – includes both raw and treated purchased surface water connections.

  15. STANDBY SOURCES: An emergency source that is not approved to be used for more than 15 calendar days per year or for periods that exceed 5 consecutive days. The local DDW District Office must be notified within 3 days after any use of a standby source. To change the status of a Standby Source to ‘Active’, a permit amendment application must be submitted to the local DDW District Office, and approval received prior to any non-emergency use of the source.

    SECTION 6. WATER RATES AND DELIVERIES.

    Click HERE to see all the help tips for this section.

  16. Residential Water Rates: Click HERE for a list of the residential water rates.

  17. Tiers rates: Click HERE for how to address flat based rates when counting tiers.

  18. Single-Family and Multi-family: Click HERE for definitions of single-family and multi-family.

  19. Residential Service Connections: Click HERE for information on how to respond to questions on residential service connection fees.

  20. HCF (hundred cubic feet): Click HERE for the meaning of HCF, also is abbreviated as CCF.

  21. Non-residential water rates: Click HERE for an explanation on the types of non-residential customers.

  22. 6 HCF, 12 HCF and 24 HCF: Click HERE for conversions of these volumes into different units.

  23. Shut-offs: Click HERE for information on how to respond to questions in this section.

  24. Residential reconnection fee: Click HERE for information on how to respond to this question.

  25. Median duration of shut-offs: Click HERE for information on how to respond to this question.

    SECTION 7. WATER QUALITY.

  26. NSF/ANSI Standard 60 Certification of Direct Additives: Pursuant to Section 64700, Title 22 of the California Code of Regulations, (effective January 1, 1994), all chemicals or products, including chlorine, added directly to the drinking water as part of a treatment process must meet the ANSI/NSF Standard 60. If you are not sure whether a chemical you are using meets this standard, contact the manufacturer or distributor of the chemical.

  27. Chemical Use Initiated in 2017: Indicate if you began using the chemical listed in 2017. Specify in the COMMENTS whether this is an additional chemical used in the treatment process or whether this chemical replaced one you are no longer using.

    SECTION 8. CROSS-CONNECTION CONTROL.

  28. Cross Connection Control: Pursuant to Title 17, California Code of Regulations, all public water systems shall protect the water supply from contamination by backflow caused by cross-connections. For premises where cross-connections are likely to occur, prevention of backflow is required through the installation of approved backflow prevention assemblies. Each backflow prevention assembly must be tested annually by a certified backflow prevention assembly tester.

  29. Backflow Prevention Assemblies: include double check valve assemblies (Fig. 1) and reduced pressure principle backflow prevention assemblies (Fig, 2) that operate to prevent water from flowing from a user’s piping back into the domestic water supply system. Each backflow prevention assembly must be tested annually by a certified backflow prevention assembly tester.
    Fig. 1 - a double check valve assembly Fig. 2 - a reduced pressure principle backflow prevention assembly

  30. Backflow Assemblies On-site: this includes backflow assemblies installed within the premises of the user, which protect the internal water distribution system from cross-connections to the satisfaction of the water supplier and health agency, such that backflow protection is not required at the user’s connection to the public water system. This also includes backflow assemblies installed within a non-community water system to protect its distribution system. Examples include backflow assemblies on the water supply to boilers, RV dump stations, commercial dishwashers, fire protection systems, etc.

  31. Air-Gap Separation: is a physical break between the water supply line and a receiving vessel, and must provide a separation of at least double the diameter of the supply pipe, measured vertically from the flood rim of the receiving vessel to the supply pipe, but in no case shall this separation be less than one inch.

  32. Inactive Backflow Prevention Assemblies: A backflow prevention assembly that is installed on a pipeline or connection that is no longer in use, as counted at the end of the calendar year 2017.

  33. Cross-Connection: is an unprotected actual or potential connection between a potable water system used to supply water for drinking purposes and any source or system containing unapproved water or a substance that is not or cannot be approved as safe, wholesome and potable. By-pass arrangements, jumper connections, removable sections, swivel or changeover devices, or other devices through which backflow could occur, shall be considered to be cross-connections.

    SECTION 9. CONSUMER CONFIDENCE REPORT.

  34. Consumer Confidence Report (CCR): Each community and nontransient noncommunity water system is required to complete a CCR on an annual basis. The CCR is to provide, as a minimum, specific information on concentration of microbiological contaminants, minerals, physical agents, inorganic chemicals, organic chemicals, and radioactivity that are present in the water supply. A template and further guidance for the preparation of the CCR can be found at the following Division of Drinking Water website: http://www.waterboards.ca.gov/drinking_water/certlic/drinkingwater/CCR.shtml

    SECTION 10. OPERATOR CERTIFICATION.

  35. Chief Operator: The person who has overall responsibility for the day-to-day, hands-on, operation of a water treatment facility or the person who has overall responsibility for the day-to-day, hands-on, operation of a distribution system.

  36. Your Highest Treatment System Classification.

    This shows the classification of your treatment facility with the highest classification (T1, T2, T3, T4, or T5). However, you may see the following instead:

    • Treatment or Distribution Operator – your treatment facility or facilities may be operated by either a certified treatment or distribution operator
    • Classification is Unavailable – the classification of your treatment facility or facilities has not been entered into the Division’s SDWIS database
    • No facilities subject to the Certified Treatment Plant Operator requirements – either you do not have any treatment facilities or these treatment facilities are not subject to the certified treatment plant operator requirements.

      If you believe that your highest treatment facility classification is in error, please notify your local regulatory agency immediately.

  37. Your Distribution System Classification.

    This shows the classification of your distribution system (D1, D2, D3, D4, or D5). However, you may see the following instead:

    • Distribution Operator Not Required – your water system is a transient non-community water system and as such is not subject to the certified distribution system operator requirements
    • Classification is Unavailable – the classification of your distribution system has not been entered into the Division’s SDWIS database

      If you believe that your highest treatment facility classification is in error, please notify your local regulatory agency immediately.

  38. Tips to Complete the Operator Certification Tables

    • If you do not have any certified operators to report, put “NONE” in each column of the first row.

      Name Grade of
      Operator
      Chief or Shift1 (C, S or X) Operator
      Number
      Expiration Date
      NONE NONE NONE NONE NONE
      - - - - -


    • Use the following format and rules to complete the State certified Water Treatment Plant Operators table:

      Treatment Operator Name Grade of
      Treatment Operator
      Chief or Shift Treatment Operator
      Number
      Treatment Certification Expiration Date
      First name Last name 1, 2, 3, 4, or 5 only. C, S or X only (lowercase ok); do not leave blank. 4 or 5 digits MM/DD/YYYY
      - - - - -
      1Use “C” for Chief Operator and “S” for Shift Operator. If neither, put an "X". Do not leave blank.

    • Use the following format and rules to complete the State certified Water Distribution System Operators table:

      Distribution Operator Name Grade of Distribution
      Operator
      Chief or Shift1 Distribution Operator
      Number
      Distribution Certificate Expiration Date
      First name Last name 1, 2, 3, 4, or 5 only. C, S or X only (lowercase ok); do not leave blank. 4 or 5 digits MM/DD/YYYY
      - - - - -
      1Use “C” for Chief Operator and “S” for Shift Operator. If neither, put an "X". Do not leave blank.

    SECTION 13. RECYCLED WATER USE.

  39. Recycled Water Use site: An area of recycled water use with defined boundaries. A use site may contain one or more facilities.

  40. Dual Plumbed: means a system that utilizes separate piping systems for recycled water and potable water within a facility and where the recycled water is used for either of the following purposes:

    1. To serve plumbing outlets (excluding fire suppression systems) within a building, or

    2. Outdoor landscape irrigation at individual residences.

    SECTION 14. SYSTEM OPERATION – TREATMENT.

  41. Watershed Sanitary Survey Report: required under the Surface Water Treatment Rule, Section 64665, as follows:

    1. All suppliers shall have a sanitary survey of their watershed(s) completed at least every five years. The first survey shall be completed by January 1, 1996.

    2. A report of the survey shall be submitted to the Department not later than 60 days following completion of the survey.

    3. The survey and report shall include physical and hydrogeological description of the watershed, a summary of source water quality monitoring data, a description of activities and sources of contamination, a description of any significant changes that have occurred since the last survey which could affect the quality of the source water, a description of watershed control and management practices, an evaluation of the system's ability to meet requirements of this chapter, and recommendations for corrective actions.

    SECTION 15. SYSTEM OPERATION – DISTRIBUTION.

  42. Date of last inspection: Last official, exhaustive tank inspection of both interior and exterior.

  43. Water Outages: Unplanned events in which the water system is depressurized and customers are out of water for any reason including water main breaks. Scheduled water outages during main replacement need not be reported. A system may be depressurized due to a well or pump failure or wildfire damage to a reservoir resulting in the reservoir being emptied.

  44. SB-555 Urban retail water suppliers: water loss management (2015-2016)

    Information in this section will be used to help develop water loss performance standards for urban retail water suppliers, as required by SB 555 (2015-16).

  45. Infrastructure and Pressure Management. Information in this section will be used to help develop water loss performance standards for urban retail water suppliers, as required by SB 555 (2015-16). Only Community Water Systems with more than 3,000 service connections or supply more than 3,300 acre feet/year need to complete these new sections: Click HERE to see all the help tips for this section.

  46. Percentage of distribution system composted of pipes with a nominal diameter. Click HERE for an explanation of nominal diameter.

  47. Pressure Managed Areas: Click HERE for an explanation of pressure managed areas.

  48. Critical Pressure Points: Click HERE for an explanation of critical pressure points.

  49. Real Loss Reduction Measures. Information in this section will be used to help develop water loss performance standards for urban retail water suppliers, as required by SB 555 (2015-16). Only Community Water Systems with more than 3,000 service connections or supply more than 3,300 acre feet/year need to complete these new sections. Click HERE to see the help tips for this section.

    SECTION 17. WATER CONSERVATION AND DROUGHT PREPAREDNESS.

  50. Units of Measure: For the 2016 EAR report and reports in prior years the answers in the section were in Millions of Gallons. You are now able to select the units to use for reporting.

  51. Projected Water Shortages: The current calendar year is January 1 to December 31, 2018.

  52. Steps to implement water efficient plumbing standards: SB 407 (2009) – “Property transfers: plumbing fixtures replacement":

    1101.1.

    (h) It is further the intent of the Legislature that retail water suppliers are encouraged to provide incentives, financing mechanisms, and funding to assist property owners with these [plumbing fixture] retrofit obligations.

    1101.8.

    A city, county, or city and county, or a retail water supplier may do either of the following:

    (a) Enact local ordinances or establish policies that promote compliance with this article.

    (b) Enact local ordinances or establish policies that will result in a greater amount of water savings than those provided for in this article.

  53. Method to implement SB 814 on excessive water use: urban retail water suppliers SB 814 (2016) refers to “Urban retail water supplier” as meaning California Water Code Section 10608.12 (p).

  54. “Urban retail water supplier” means a water supplier, either publicly or privately owned, that directly provides potable municipal water to more than 3,000 end users or that supplies more than 3,000 acre-feet of potable water annually at retail for municipal purposes.

  55. Comments regarding SB814: You may include a web link in your comments.

    SECTION 18. CLIMATE CHANGE.

  56. Only community water systems need to complete this section. A community water system is a public water system that serves at least 15 service connections used by yearlong residents or regularly serves at least 25 yearlong residents of the area served by the system. It typically includes cities, residential areas, mobile home parks, etc. This section is not required for non-transient non-community, or transient non-community water systems (typically includes campgrounds, restaurants, factories, business parks).

    The State Water Board passed a resolution on March 3, 2017 requiring a proactive approach to climate change in all Board actions, with the intent to embed climate change consideration into all programs and activities. For more information on climate change, please click HERE.

  57. Climate Threats: Check each box that applies. You may check more than one box.

  58. Sensitivity and Magnitude of Impacts: Qualitatively assess sensitivity of your facilities, and plausibility of failure using past experience, and expert judgement based on the magnitude of expected threats in the future. You do not need numeric answers. Consider the criticality or consequence of disruption to understand the scale and scope of the risk posed by changing conditions and extreme events. For each type of climate change impact or row in this section, you may choose one response.

    Resources are available that may help you complete this section:


  59. Adaptation Measures: Identify measures to reduce current vulnerability, or make future modifications based on identified sensitivity of the water system. Indicate status for all projects that your organization has completed, or plan to implement to increase resiliency of the water system to climate change. USEPA’s Adaptation Strategies Guide for Water Utilities provides examples of adaptation: https://www.epa.gov/crwu/learn-how-plan-extreme-weather-events. For each adaptation measure or row in this section, you may choose one response.